Register here

Author Topic: Advancedboy's Designs Topic  (Read 96681 times)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #255 on: June 29, 2016, 02:54:50 am »
T-X updated.
If you are hotter than me, I must be cooler than you:)

Offline riggerrob

  • CLEARANCE: Secret
  • **
  • Posts: 187
  • I really should change my personal text
Re: Advancedboy's Designs Topic
« Reply #256 on: June 29, 2016, 02:34:17 pm »
Clever the way you have integrated engines with wings on those transports.

However, on the jet hydroplane, I would crank the wings in the other direction because bolting the wings' center section directly to the fuselage would shorten load-paths and reduce interference drag. Then crank the outer wings upwards outboard of the engine nacelles. High outer wing panels will whack fewer docks, trucks, fork-lifts, etc.

The greatest challenge is making it maneuverable enough to reverse onto docks so that it can unload straight out the back end. Thrust-reversers pointing up, over top of the wings?

Either way, you still need to keep engine inlets well above the waves to minimize water-ingestion. Floats will help reduce spray directly into engine intakes.

Sorry dude, I was not trying to tell you how to draw your pretty pictures. ..... Instead, I was looking at your sketches from a truck-driver's perspective and trying to figure out the easiest way to unload cargo.

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #257 on: July 01, 2016, 10:26:52 am »
Thanks Riggerbob, I will consider your suggestions once I return to update that sketch.
Anyways, here is a TR-3X classified medium range bomber flying over your heads:)
If you are hotter than me, I must be cooler than you:)

Offline MaxLegroom

  • CLEARANCE: Confidential
  • *
  • Posts: 114
  • Why not?
Re: Advancedboy's Designs Topic
« Reply #258 on: July 17, 2016, 02:06:01 pm »
Future Medium Cargo  for Boeing. Initial doodle. Possible engine integration into wings.
Interesting, but I wouldn't want to have to work on that wing structure, and it'd be expensive to engineer and manufacture.  Burying the engines in the wings is uncommon for a reason, though, having to do with airflow (see DeHavilland Comet), and drag. 

Rather impressive artwork, though.

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #259 on: November 10, 2016, 12:40:27 pm »
Further development of  my sketch at  Reply #249. N-GAD. Rear stabilizer vectoring. Upper position and medium low position. The lowest position will have a flat alignment with the main wing.
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #260 on: November 12, 2016, 10:17:06 am »
NGAD. Top view. The rotating vertical stabilizers at their lowest position and alignment with the wing. As they are rotating on a hub around engine exhaust assembly ( this idea was developed as it offered enough power shoulder to support a movable stabilizer) they could be rotating at negative angles as well. That is, below alignment line with the wing.
« Last Edit: November 12, 2016, 10:21:46 am by ADVANCEDBOY »
If you are hotter than me, I must be cooler than you:)

Offline pedrospe

  • CLEARANCE: Secret
  • **
  • Posts: 225
Re: Advancedboy's Designs Topic
« Reply #261 on: November 12, 2016, 10:42:20 am »
Very nice concept.

  best regards

  Pedro

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #262 on: January 15, 2017, 08:18:56 am »
Thank You for your support. Here I added a sketch for a future Ford Pickup Truck .
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #263 on: January 15, 2017, 09:00:16 am »
A sketch of a Bell 599 rescue helicopter and FATSO UAV slightly updated.
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #264 on: January 22, 2017, 03:26:57 am »
Next generation Dodge Durango.
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #265 on: March 20, 2017, 11:34:04 am »
 I decided to rework Bell FCX-001. Initially I wanted to modify it  just slightly, but in the end I redesigned all of it just leaving the main rotor intact. I t turned out a bit classic, not futuristic or conceptual enough but at least it retains some Bell family design features.
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #266 on: April 09, 2017, 08:17:47 am »
Boeing HI-Octane.
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #267 on: July 07, 2017, 08:45:34 am »
Ford Mustang 2020.
If you are hotter than me, I must be cooler than you:)

Offline ADVANCEDBOY

  • CLEARANCE: Secret
  • **
  • Posts: 265
Re: Advancedboy's Designs Topic
« Reply #268 on: Yesterday at 11:46:25 pm »
A hydroplane. Initial raw sketch. Top view. An iso view might come if you are interested.
If you are hotter than me, I must be cooler than you:)